AXIAL SCX24 Off-Road Driveline Kit Harden Steel #45 Front CVDs + Extended Rear Shafts + Brass Weights SCX247FRSX+5 by GPM  [SCX247FRSX+5]

AXIAL 4WD SCX24 DEADBOLT Harden Steel #45 Front CVD Joint+Rear Drive Shaft + Brass Pendulum Wheel Knuckle Axle Weight - 8 pcs set - GPM SCX247FRSX+5
Price:
NZD$40.96
Brand:
GPM
Model:
SCX247FRSX+5
GTIN:
4894538343519
Condition:
Brand New
Write a review
alt="AXIAL 4WD SCX24 DEADBOLT Harden Steel #45 Front CVD Joint+Rear Drive Shaft + Brass Pendulum Wheel Knuckle Axle Weight - 8 pcs set - GPM SCX247FRSX+5" title="AXIAL 4WD SCX24 DEADBOLT Harden Steel #45 Front CVD Joint+Rear Drive Shaft + Brass Pendulum Wheel Knuckle Axle Weight - 8 pcs set - GPM SCX247FRSX+5"
alt="AXIAL 4WD SCX24 DEADBOLT Harden Steel #45 Front CVD Joint+Rear Drive Shaft + Brass Pendulum Wheel Knuckle Axle Weight - 8 pcs set - GPM SCX247FRSX+5" title="AXIAL 4WD SCX24 DEADBOLT Harden Steel #45 Front CVD Joint+Rear Drive Shaft + Brass Pendulum Wheel Knuckle Axle Weight - 8 pcs set - GPM SCX247FRSX+5"
alt="AXIAL 4WD SCX24 DEADBOLT Harden Steel #45 Front CVD Joint+Rear Drive Shaft + Brass Pendulum Wheel Knuckle Axle Weight - 8 pcs set - GPM SCX247FRSX+5" title="AXIAL 4WD SCX24 DEADBOLT Harden Steel #45 Front CVD Joint+Rear Drive Shaft + Brass Pendulum Wheel Knuckle Axle Weight - 8 pcs set - GPM SCX247FRSX+5"
alt="AXIAL 4WD SCX24 DEADBOLT Harden Steel #45 Front CVD Joint+Rear Drive Shaft + Brass Pendulum Wheel Knuckle Axle Weight - 8 pcs set - GPM SCX247FRSX+5" title="AXIAL 4WD SCX24 DEADBOLT Harden Steel #45 Front CVD Joint+Rear Drive Shaft + Brass Pendulum Wheel Knuckle Axle Weight - 8 pcs set - GPM SCX247FRSX+5"

Driveline and hub ballast upgrade for SCX24

This 8-piece set is an RC-scale driveline upgrade intended for AXIAL 1/24 SCX24 chassis. It pairs #45 hardened steel front CVD joints with longer rear drive shafts and brass pendulum wheel weights to alter hub mass and track width without altering the base chassis layout.

Brass pendulum weights concentrate mass at the wheel hubs to improve traction on steep climbs and when exiting shallow depressions. The front CVDs are made from hardened #45 steel for strength, and the rear shafts are increased in length by 5mm over stock to widen the stance and aid lateral control.

Packing includes

  • Front CVD joint - 2pcs
  • Rear drive shaft - 2pcs
  • Pendulum Wheel Weight - 4pcs

Original Name / Part No:

AXI31610+AXI31609

Compatible Models

  • AXIAL-1/24 4WD SCX24 DEADBOLT-AXI90081
  • AXIAL-1/24 JEEP WRANGLER JLU CRC-AXI00002

Choose this set if you want improved tyre contact and a slightly wider track on AXIAL 1/24 SCX24 rigs; the hardened front CVDs, longer rear shafts and 15 g pendulums help with steady low-speed crawling and better recovery from obstacles.

What parts are in the SCX247FRSX+5 package?

You get two front CVDs, two rear drive shafts and four brass pendulum wheel weights, totalling eight components to swap into the driveline.

Compatibility with SCX24 models?

The compatible list in the box names AXIAL-1/24 4WD SCX24 DEADBOLT-AXI90081 and an SCX24-based Jeep model; inspect your vehicle's axle spacing to confirm fit.

Will the added weight slow acceleration?

Adding brass at the hubs slightly increases unsprung mass and can mellow quick acceleration, but it noticeably improves traction and control during technical crawling.

Do I need special tools to fit these parts?

Basic hand tools and small hex drivers are sufficient; ensure retaining hardware is torqued correctly and check for clearance through suspension travel after installation.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved