AXIAL SCX6 Scale Front Bumper 6061 T6 SCX6330F by GPM  [SCX6330F]

AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F
Price:
NZD$124.95
Brand:
GPM
Model:
SCX6330F
GTIN:
4894538357479
Condition:
Brand New
Write a review
alt="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F" title="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F"
alt="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F" title="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F"
alt="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F" title="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F"
alt="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F" title="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F"
alt="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F" title="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F"
alt="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F" title="AXIAL SCX6 JEEP JLU WRANGLER 4WD Aluminium Front Bumper With D-rings - 15pc set - GPM SCX6330F"

Overview of the front bumper

This aluminium front bumper is intended for the AXIAL SCX6 platform and tailored to the 1/6 4WD SCX6 JEEP JLU WRANGLER. Constructed from 6061 T6 aluminium and finished anodized to limit corrosion, the assembly balances strength with a lightweight profile suitable for scale rock crawling and trail work. Part location: front bumper.

The package contains two D-rings, dedicated 5mm LED holders and the stainless steel fasteners and shims needed for mounting. The bumper offers a reinforced contact surface to reduce impact transfer to the chassis and provides realistic mounting points for lights and recovery gear.

Installation guidance: secure the bumper to the vehicle front using the included screws. Ensure correct alignment and full thread engagement when installing the stainless screws, and fit the shims where indicated to achieve even seating and accurate LED holder alignment.

Packing includes

  • Bumper Base - 1pcs
  • Bumper Top - 1pcs
  • Bumper Secure Post - 2pcs
  • SCX6330F D-Ring - 2pcs
  • Stainless steel Cap Head Screws 2.5*12 - 2pcs
  • Stainless steel Round Head Screw 2x4 - 2pcs
  • Stainless steel Flat Head Screw 5x12 - 2pcs
  • Stainless steel Shim 2*7*0.3 - 2pcs
  • 5MM LED light - 1pcs

Original Name / Part No:

AXI250002

Compatible Models

  • 1/6 4WD SCX6 JEEP JLU WRANGLER-AXI05000

Built for scale realism and practical protection, this anodized 6061 T6 bumper for AXIAL SCX6 adds LED accommodation and D-ring recovery points while keeping clearance to other chassis elements.

Is wiring for LEDs included with the bumper?

The kit includes one 5MM LED and the holders; it does not include pre-wired leads, so plan to solder or extend wiring to your lighting harness as required.

Are the D-rings rated for recovery pulls?

The D-rings provide scale recovery points for light pulls and winch setups, but avoid heavy loads that could stress bumper mounts or chassis components.

Do I need extra parts to fit this bumper?

Most installations use the supplied screws and shims; check for any aftermarket skid or bumper mods on your truck that may require additional brackets or spacers.

How should I protect the finish?

Touch up small scratches with anodized-safe coatings or keep the bumper clean and dry after wet runs to preserve the anodized surface.

Will the bumper change steering geometry?

When fitted as instructed the bumper should not alter steering geometry; verify there is no contact with steering linkages during full lock checks after installation.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved