AXIAL SMT10 Adjustable Aluminium Shock Mount Front and Rear MJ028 by GPM  [MJ028]

AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028
Price:
NZD$20.40
Brand:
GPM
Model:
MJ028
GTIN:
4894538263534
Condition:
Brand New
Write a review
alt="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028" title="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028"
alt="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028" title="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028"
alt="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028" title="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028"
alt="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028" title="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028"
alt="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028" title="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028"
alt="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028" title="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028"
alt="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028" title="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028"
alt="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028" title="AXIAL Racing SMT10 Aluminium Front/Rear Adjustable Shock Mount - 1pr set - GPM MJ028"

Adjustable Shock Mount for SMT10

This aluminium adjustable shock mount is an aftermarket part tailored to AXIAL SMT10 vehicles and identified by part number MJ028. Packed as a 1pr set, it swaps in for the stock front and rear mounts to provide additional shock body and ball locations without changing the shock assemblies.

Move the mount to alter shock angles and leverage during setup; repositioning affects damping feel and roll characteristics and helps dial in a mix of grip and responsiveness. The metal construction is stiffer than the standard plastic pieces and keeps alignment steadier under load.

Fitting is straightforward on SMT10 formats that share the standard mounting pattern and normally uses the existing screws and hardware. After installation, verify ball ends and shafts operate freely through full travel and make sure all fasteners are secure before driving.

Will these mount to my SMT10 without modification?

They are intended for SMT10-style mounting patterns and in most cases fit directly, but check the fit on your specific chassis before final tightening.

Does one purchase cover both axle ends?

The item is sold as a paired set, supplying both front and rear mounts so you get matched geometry front to back.

How should I test after fitting?

Cycle the suspension through full travel to check for binding, confirm ball joint clearance, and re-tighten fasteners after the first short run.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved