AXIAL SMT10 Machined Aluminium Wheel Hex +2mm MJ0104/+2MM by GPM  [MJ0104/+2MM]

AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM
Price:
NZD$15.25
Brand:
GPM
Model:
MJ0104/+2MM
GTIN:
4894538264470
Condition:
Brand New
Write a review
alt="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM" title="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM"
alt="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM" title="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM"
alt="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM" title="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM"
alt="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM" title="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM"
alt="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM" title="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM"
alt="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM" title="AXIAL Racing SMT10 Aluminium Wheel Hex (+2mm) - 4pcs set - GPM MJ0104/+2MM"

Machined aluminium wheel hex with +2mm offset

Supplied as a 4pcs set, this aluminium wheel hex is an aftermarket item made for AXIAL Racing SMT10 wheel assemblies to provide a +2mm outward offset. It lets you correct rubbing or fine tune wheel stance without swapping wheels or hubs.

Installation follows standard procedures for SMT10 hex swaps: remove wheel and original hex, fit the aluminium hex to the axle or hub in the correct orientation, then refit and tighten the wheel hardware. After fitting, verify wheel clearance at full suspension travel and make sure pins and screws are secure to prevent loosening in use. The product uses machining-grade aluminium for a durable mounting component.

The package also contains common hardware to complete installation, included exactly as supplied:

  • 2x10.9 Steel Pin - 4pcs
  • 2x7 Steel Pin - 4pcs
  • 2.5x2.5 Screw Shaft - 8pcs
  • 1.2 Hex Socket Key - 1pc

Does the MJ0104/+2MM change handling significantly?

The modest +2mm offset is mainly for clearance and stance; it should not drastically alter handling but will slightly change track width and tyre scrub characteristics.

Is the hardware supplied with the hex?

Yes, the set ships with the pins, screw shafts and the 1.2 hex key listed in the package contents so you have what is needed for a standard swap.

Any fit checks to do after fitting?

Check wheel clearance at full lock and suspension travel, and recheck fastener tightness after initial runs to ensure nothing loosens.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved