CC-01 70mm Nylon Front Ball-Top Damper CC070NF for TAMIYA by GPM  [CC070NF]

Tamiya CC-01 Nylon Front Ball Top Damper (70mm) With Alloy Body & Ball Ends - 1pr set - GPM CC070NF
Price:
NZD$28.32
Brand:
GPM
Model:
CC070NF
GTIN:
4894538031706
Condition:
Brand New
Write a review
alt="Tamiya CC-01 Nylon Front Ball Top Damper (70mm) With Alloy Body & Ball Ends - 1pr set - GPM CC070NF" title="Tamiya CC-01 Nylon Front Ball Top Damper (70mm) With Alloy Body & Ball Ends - 1pr set - GPM CC070NF"
alt="Tamiya CC-01 Nylon Front Ball Top Damper (70mm) With Alloy Body & Ball Ends - 1pr set - GPM CC070NF" title="Tamiya CC-01 Nylon Front Ball Top Damper (70mm) With Alloy Body & Ball Ends - 1pr set - GPM CC070NF"
alt="Tamiya CC-01 Nylon Front Ball Top Damper (70mm) With Alloy Body & Ball Ends - 1pr set - GPM CC070NF" title="Tamiya CC-01 Nylon Front Ball Top Damper (70mm) With Alloy Body & Ball Ends - 1pr set - GPM CC070NF"
alt="Tamiya CC-01 Nylon Front Ball Top Damper (70mm) With Alloy Body & Ball Ends - 1pr set - GPM CC070NF" title="Tamiya CC-01 Nylon Front Ball Top Damper (70mm) With Alloy Body & Ball Ends - 1pr set - GPM CC070NF"
alt="Tamiya CC-01 Nylon Front Ball Top Damper (70mm) With Alloy Body & Ball Ends - 1pr set - GPM CC070NF" title="Tamiya CC-01 Nylon Front Ball Top Damper (70mm) With Alloy Body & Ball Ends - 1pr set - GPM CC070NF"

70mm Ball-Top Front Damper Compatible with TAMIYA CC-01

The CC070NF is an aftermarket 70mm front ball-top damper intended for TAMIYA CC-01 scale chassis where a ball-top mounting is used. The design combines a nylon ball-top with an alloy damper body and ball-end connectors to provide a straightforward replacement or upgrade option.

Supplied as a single pair, this component is aimed at routine servicing, part replacement, and small suspension tune-ups on electric scale RC vehicles. Installation follows standard front shock mounting procedures and uses the existing ball studs; common hex drivers are adequate.

Functionally, the nylon ball-top lowers friction at the joint while the alloy body contributes to improved wear resistance. After installation, confirm ball-end seating and thread engagement, then re-establish preload and ride height as required for correct handling.

Specifications

  • Item Front Ball Top Damper (70mm), 1pr set
  • Material Nylon top, alloy body, ball ends
  • Model Number CC070NF
  • Compatibility TAMIYA CC-01 chassis

A handy replacement for builders who want a 70mm front ball-top unit that matches CC-01 geometry and supports straightforward suspension adjustments.

This item is compatible with

  • TAMIYA CC01

Will the ball-top fit stock CC-01 mounts?

Yes, where the CC-01 uses ball-top front mounts this 70mm unit is intended as a direct-fit; always check your specific shock tower spacing first.

Can I reuse my original springs?

You can reuse springs if they match the replacement shock length and mounting, but adjust spring rate and oil to suit your handling target.

What routine maintenance is recommended?

Periodically check ball sockets for wear, inspect the alloy body for damage, and verify damping oil and spring condition for consistent performance.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved