HPI Bullet 3.0 MT and ST Rear Knuckle Arm Alloy BMT022 by GPM  [BMT022]

HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022
Price:
NZD$26.64
Brand:
GPM
Model:
BMT022
GTIN:
4894538028010
Condition:
Brand New
Write a review
alt="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022" title="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022"
alt="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022" title="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022"
alt="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022" title="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022"
alt="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022" title="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022"
alt="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022" title="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022"
alt="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022" title="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022"
alt="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022" title="HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set - GPM BMT022"

Alloy rear knuckle designed for Bullet 3.0

This pair of rear knuckle arms is manufactured to fit HPI Bullet 3.0 MT and ST vehicles and is supplied as a 1pr set. The component is a direct-fit alloy replacement for the rear steering knuckle assembly and aligns with the original mounting layout.

Install these knuckles to replace damaged rear steering arms or to fine tune rear suspension geometry. The design keeps hub and linkage positions consistent with the factory layout. Fitting requires common RC maintenance tools and basic suspension setup knowledge.

Specifications

  • Item: HPI Bullet 3.0 Mt And St Alloy Rear Knuckle Arm - 1pr set
  • Material: Alloy
  • Model Number: GPM BMT022
  • Compatibility: HPI Bullet 3.0 MT and ST (Nitro Engines)

Ideal when you need a dependable alloy replacement for Bullet 3.0 rear steering, or when adjusting setup during maintenance and tuning sessions.

Is this compatible with both MT and ST Bullet 3.0 variants?

Yes, it is intended to replace the rear knuckle on both the MT and ST Bullet 3.0 chassis using the same mounting points.

Any special alignment required after fitting?

After installation check toe and camber as part of routine setup; small adjustments may be needed depending on your drivetrain and tyre choice.

Can I reuse my original bearings?

Bearings and hardware are not included, so inspect and reuse serviceable items or replace them if worn to ensure smooth operation.

Will alloy knuckles require different maintenance?

Alloy parts are durable but check for thread wear and secure fasteners regularly as part of normal RC maintenance.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved