Mini-Z AWD Rear Knuckle Arm Holder Upgrade Alloy, -0.2mm Toe 0.6mm MZA031R-0206 by GPM  [MZA031R-0206]

Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206
Price:
NZD$8.04
Brand:
GPM
Model:
MZA031R-0206
GTIN:
4894538121902
Condition:
Brand New
Write a review
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"

Precision alloy knuckle arm holder for Mini-Z AWD

This replacement alloy rear knuckle arm holder is crafted for Kyosho Mini-Z AWD rear assemblies and sold as a single unit. It delivers a set rear Toe Out of -0.2mm and uses a 0.6mm thick plate suitable for fine tuning the rear toe angle.

The alloy part is intended as a direct replacement or an upgrade where consistent geometry and minimal flex are priorities during regular use. Always double-check fit on your Mini-Z AWD chassis and ensure the toe setting suits your handling preferences.

Assembly note: orient the bracket correctly, tighten mounting hardware to the recommended torque, and inspect clearance throughout full suspension movement. Supplied as 1 pcs.

Is this compatible with tuned or modded Mini-Z AWDs?

Compatibility is based on stock Mini-Z AWD rear knuckle dimensions; modified or heavily altered chassis may need a trial fit to confirm clearance and alignment.

Should I use this for big handling changes?

No. The -0.2mm toe out is designed for incremental adjustments to refine balance rather than large setup overhauls.

How many pieces are included?

The item is supplied as a single piece, indicated as 1 pcs in the listing.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved