Slash 4X4 Aftermarket Front C Hub 7075 Alloy SLA019N by GPM  [SLA019N]

TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N
Price:
NZD$49.53
Brand:
GPM
Model:
SLA019N
GTIN:
4894538387933
Condition:
Brand New
Write a review
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"

Aftermarket front C hub for Slash 4X4

The SLA019N front C hub is an aftermarket replacement made for TRAXXAS Slash 4X4 and a range of 1/10 4WD platforms. Built from 7075 alloy, the hub repositions the knuckle to ride on a bearing rather than a plain shaft hole to cut steering slop and improve feedback. Multiple upper tie rod holes let you adjust roll centre and toe without swapping other suspension pieces.

Installation uses the stock C-hub mounting points and the included hardware for a direct changeover. Ensure bearings seat correctly in the knuckle and use thread-lock on metal screws where appropriate. This component is intended for hobby RC application only and matches the models listed below.

Packing includes

  • C-Hub - 1pcs
  • King Pin - 1pcs
  • Grade 12.9 black Round Head Screws 3x14 - 1pcs
  • Grade 12.9 black Round Head Screws 3x16 - 1pcs

Original Name / Part No:

6832

Compatible Models

  • TRAXXAS-SLASH 4X4 LOW-CG-68086-21
  • TRAXXAS 1/10 RUSTLER 4X4 VXL-67076-4
  • TRAXXAS 1/10 4WD HOSS 4X4 VXL 3S-90076-4
  • TRAXXAS 1/10 Ford Fiesta ST Rally-74064-4
  • TRAXXAS 1/10 Ford Fiesta ST Rally-74054-4
  • TRAXXAS 1/10 Rustler 4X4-67064-1
  • TRAXXAS 1/10 Rustler 4X4-67064-61
  • TRAXXAS 1/10 Slash 4X4 VXL-68086-4
  • TRAXXAS 1/10 Slash 4X4-68054-1
  • TRAXXAS 1/10 Slash 4X4-68054-61
  • TRAXXAS 1/10 Slash 4X4 VXL-68286-4
  • TRAXXAS 1/10 Stampede 4X4 VXL-67086-4
  • TRAXXAS 1/10 Rustler 4X4 Ultimate-67097-4
  • TRAXXAS 1/10 Slash 4X4 Ultimate-67097-4
  • TRAXXAS 1/10 Slash 4X4 Ultimate-68277-4

Fit this SLA019N hub to reduce knuckle movement and sharpen steering response; experiment with upper tie rod positions to suit tarmac or loose surfaces, and double-check bearing fit and screw locking during fitment.

Does the SLA019N require any chassis mods to fit?

No chassis modification is usually required if your model code matches one listed in the Compatible Models box; the hub uses the stock front mounting points for a direct swap.

Should I reuse my existing king pin and screws?

The package contains a king pin and specified screws. You can reuse serviceable hardware from your original hub, but use the supplied parts for guaranteed fit and correct thread engagement.

Is this part compatible with 3S setups?

The hub is a structural steering component; verify your motor and ESC loads are within normal limits for your vehicle. The SLA019N itself is made from 7075 alloy which increases stiffness over plastic options.

How do I check bearing seating after install?

After assembly, spin the wheel and check for smooth rotation and no axial play at the knuckle. Tighten screws incrementally and recheck to avoid preloading bearings.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved