Slash 4x4 Rear CVD Upgrade SSLA1277RH - Steel/Aluminium by GPM  [SSLA1277RH]

TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH
Price:
NZD$59.28
Brand:
GPM
Model:
SSLA1277RH
GTIN:
4894538073942
Condition:
Brand New
Available in shop
Write a review
alt="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH" title="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH"
alt="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH" title="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH"
alt="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH" title="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH"
alt="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH" title="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH"
alt="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH" title="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH"
alt="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH" title="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Rear CVD Drive Shaft With 12mmx6mm Wheel Hex - 1pr set - GPM SSLA1277RH"

Rear CVD upgrade for Slash 4x4 drivetrains

This rear CVD drive shaft is an aftermarket replacement made for 1/10 TRAXXAS Slash 4x4 and supplied as a 1pr set by GPM (SSLA1277RH). The design mixes steel and aluminium pieces to improve durability and allow straightforward servicing.

The shaft replaces the factory rear unit and includes a revised CVD head plus a 12mmx6mm wheel hex to secure the wheel interface. Adjustable length lets you tune fitment on Slash 4x4 variants where space and splines permit.

Targeted at hobbyists who tune drivetrains, installation normally requires swapping rear shafts, checking suspension and gearbox clearance, and ensuring the CVD head meshes properly with the outdrive before first run.

Specifications

  • Item Rear CVD drive shaft with 12mmx6mm wheel hex, 1pr set
  • Material Steel and aluminium
  • Model Number GPM SSLA1277RH
  • Compatibility TRAXXAS 1/10 Slash 4x4

Fit this shaft only where the Slash 4x4 geometry allows an aftermarket CVD; confirm spline, hex and clearances, then fine tune length and alignment for dependable performance.

This item is compatible with

  • TRAXXAS Slash 4X4

Is SSLA1277RH compatible with stock Slash 4x4 hubs?

Compatibility depends on your hub and outdrive specifications; confirm spline count and that the 12mmx6mm hex matches your wheels before installation.

Can I shorten or lengthen the shaft easily?

Yes, length is adjusted by the shaft assembly position and securing method at the CVD head; always check with suspension at extremes to avoid binding.

What should I inspect at first service?

Inspect joints for wear or play, clear away dirt and grit, and lightly lubricate moving parts while keeping the wheel hex area clean for secure retention.

Does the package include instructions or hardware?

The item is sold as the drive shaft with 12mmx6mm wheel hex; check the seller notes for included screws or fitting instructions if they are required.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved