Tamiya GF01 Front and Rear 38mm Steel CVD Shafts 12x6mm Hex GF1238SADT by GPM  [GF1238SADT]

Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT
Price:
NZD$34.77
Brand:
GPM
Model:
GF1238SADT
GTIN:
4894538035407
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
category
Write a review
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"

Overview of 38mm GF01 CVD shafts

This replacement pair of front and rear CVD shafts is supplied as a robust steel upgrade for the Tamiya GF01 chassis, intended to substitute softer stock drive parts. The components are manufactured from #45 steel, sized at 38mm, and include 12x6mm hex adapters for standard GF01 wheel hubs.

The design preserves factory GF01 fitment points while increasing resistance to twisting and general wear versus plastic or softer alloys. Suitable for hobby-scale 1/10 GF01 touring and off-road models that use the specified shaft length and hex adapter sizing.

Fitment advice: confirm your vehicle uses the GF01 standard CVD length and 12x6mm hex interface ahead of installation, check pin and bearing condition when reassembling, and run a low-speed check to ensure there is no binding.

Specifications

  • Item: Front/Rear CVD shaft set
  • Material: Steel #45
  • Model Number: GF1238SADT
  • Compatibility: Tamiya GF01
  • Length: 38mm
  • Includes: 12x6mm hex adapters
  • Quantity: 1 pr set

A practical steel replacement for GF01 owners who need a stiffer, longer-lasting driveshaft solution while retaining original drivetrain geometry; always verify dimensions for your specific GF01 build.

Can I use these on a converted GF01 with different wheel offsets?

If your conversion keeps the original CVD length and 12x6mm wheel hex interface, these will fit; if you have altered offsets or axle spacing, remeasure before fitting.

Are retention pins or bearings supplied?

The package lists the steel CVD shafts and 12x6mm hex adapters only; pins, bearings and other small hardware are not specified as included.

Will steel shafts increase drivetrain wear?

Steel increases torsional strength and can shift wear to mating components; inspect mating pins and bearings regularly and ensure proper lubrication of splines where applicable.

What hex size is included for wheels?

The set includes 12x6mm hex adapters to match common GF01 wheel hex mounts; confirm your wheels use that standard before fitting.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved