TRAXXAS 1/8 X-Maxx Rear Suspension Holder Aluminium TXM300R by GPM  [TXM300R]

TRAXXAS 1/8 X-Maxx Aluminium Rear Suspension Holder - 1pc set - GPM TXM300R
Price:
NZD$55.45
Brand:
GPM
Model:
TXM300R
GTIN:
4894538168648
Condition:
Brand New
Write a review
alt="TRAXXAS 1/8 X-Maxx Aluminium Rear Suspension Holder - 1pc set - GPM TXM300R" title="TRAXXAS 1/8 X-Maxx Aluminium Rear Suspension Holder - 1pc set - GPM TXM300R"
alt="TRAXXAS 1/8 X-Maxx Aluminium Rear Suspension Holder - 1pc set - GPM TXM300R" title="TRAXXAS 1/8 X-Maxx Aluminium Rear Suspension Holder - 1pc set - GPM TXM300R"
alt="TRAXXAS 1/8 X-Maxx Aluminium Rear Suspension Holder - 1pc set - GPM TXM300R" title="TRAXXAS 1/8 X-Maxx Aluminium Rear Suspension Holder - 1pc set - GPM TXM300R"
alt="TRAXXAS 1/8 X-Maxx Aluminium Rear Suspension Holder - 1pc set - GPM TXM300R" title="TRAXXAS 1/8 X-Maxx Aluminium Rear Suspension Holder - 1pc set - GPM TXM300R"
alt="TRAXXAS 1/8 X-Maxx Aluminium Rear Suspension Holder - 1pc set - GPM TXM300R" title="TRAXXAS 1/8 X-Maxx Aluminium Rear Suspension Holder - 1pc set - GPM TXM300R"

Rear aluminium mount for X-Maxx chassis

This aluminium rear suspension holder is an aftermarket replacement crafted for the TRAXXAS 1/8 X-Maxx chassis, supplied as a single-piece unit. It acts as the structural mounting point for the rear suspension linkage and is suited to maintenance, repair and tuning of the specified model.

Manufactured from machined aluminium, the part provides a stiffer option compared with the original plastic component, helping to hold alignment under stress and giving a more durable surface for the rear suspension assembly. It is supplied as one pcs and matches the form used on the 1/8 X-Maxx rear end.

Installation uses the vehicle's existing hardware and mounting points to replace the corresponding rear holder, keeping factory geometry intact while enabling easier tuning and longer term durability in demanding conditions.

Specifications

  • Item Rear Suspension Holder - 1 pcs
  • Material Aluminium
  • Model Number TXM300R
  • Compatibility TRAXXAS 1/8 X-Maxx

This direct-fit aluminium replacement is aimed at enthusiasts who want a tougher rear suspension mount for regular setup work and heavier running without altering chassis geometry.

This item is compatible with

  • TRAXXAS XMAXX
  • TRAXXAS X MAXX 8S Monster Truck

Can I reuse the original bolts when fitting this part?

Yes, the holder is designed to accept the vehicle's existing hardware and mounts in the same locations as the original part.

Does the aluminium part require any special maintenance?

Periodic inspection for bolts and signs of wear is recommended, but aluminium does not require the same replacement rate as plastic parts under similar loads.

Will shocks or links need adjustment after fitting?

Because the holder preserves factory geometry, major setup changes are not normally required, though you should check alignment and clearances during installation.

Is the part compatible with all X-Maxx variants?

The TXM300R is specified for the TRAXXAS 1/8 X-Maxx rear assembly; confirm fitment against your vehicle's rear end before purchase.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved