TRAXXAS MAXX 1/10 Aluminium Front Knuckles TXMS021N by GPM  [TXMS021N]

TRAXXAS MAXX MONSTER TRUCK Aluminum 7075-T6 Front Steering Blocks - GPM TXMS021N
Price:
NZD$61.83
Brand:
GPM
Model:
TXMS021N
GTIN:
4894538372571
Condition:
Brand New
Write a review
alt="TRAXXAS MAXX MONSTER TRUCK Aluminum 7075-T6 Front Steering Blocks - GPM TXMS021N" title="TRAXXAS MAXX MONSTER TRUCK Aluminum 7075-T6 Front Steering Blocks - GPM TXMS021N"
alt="TRAXXAS MAXX MONSTER TRUCK Aluminum 7075-T6 Front Steering Blocks - GPM TXMS021N" title="TRAXXAS MAXX MONSTER TRUCK Aluminum 7075-T6 Front Steering Blocks - GPM TXMS021N"
alt="TRAXXAS MAXX MONSTER TRUCK Aluminum 7075-T6 Front Steering Blocks - GPM TXMS021N" title="TRAXXAS MAXX MONSTER TRUCK Aluminum 7075-T6 Front Steering Blocks - GPM TXMS021N"
alt="TRAXXAS MAXX MONSTER TRUCK Aluminum 7075-T6 Front Steering Blocks - GPM TXMS021N" title="TRAXXAS MAXX MONSTER TRUCK Aluminum 7075-T6 Front Steering Blocks - GPM TXMS021N"
alt="TRAXXAS MAXX MONSTER TRUCK Aluminum 7075-T6 Front Steering Blocks - GPM TXMS021N" title="TRAXXAS MAXX MONSTER TRUCK Aluminum 7075-T6 Front Steering Blocks - GPM TXMS021N"

Aluminium front steering knuckles tailored for TRAXXAS MAXX

These aluminium steering blocks are machined from 7075-T6 alloy to strengthen the front knuckle area and replace the stock plastic knuckles with a metal option. The shapes are streamlined for a contemporary look while maintaining the TRAXXAS MAXX front mounting points.

Two tie-rod mounting holes give alternate link positions so you can alter the steering link angle and fine-tune steering behaviour on the model. This feature is for RC setup adjustments only and is not applicable to real vehicles.

Installation notes: the items include the knuckle arms and the stainless steel screws shown below, and they use the original steering linkage pattern. During fitting, verify screw torque and ensure suspension and servo clearances to avoid any binding.

Packing includes

  • Kncukle arm - 2pcs
  • Stainless steel round head screw 3x16 - 2pcs

Original Name / Part No:

8937

Compatible Models

  • TRAXXAS-1/10 4WD MAXX MONSTER TRUCK -89076-4
  • TRAXXAS-1/10 4WD MAXX W/WIDE MAXX MONSTER TRUCK-89086-4

Choose these aluminium front steering blocks for a tougher metal replacement and easy tie-rod geometry adjustments on TRAXXAS MAXX 1/10 models; always check installation fitment first.

Do these replace the factory front knuckles directly?

Yes, they use the same mounting pattern as the factory knuckles and come with the stainless screws required for proper installation.

Will the tie-rod change affect bump steer?

Moving the tie-rod alters the steering link angle which can influence bump steer characteristics; evaluate changes on a controlled run and tune incrementally.

Are additional screws needed?

No extra screws are normally required; the kit supplies two stainless steel round head screws 3x16 for front mounting as listed in the packing section.

How should I check for binding after fitment?

After mounting, cycle the steering by hand and at low speed, inspect for rubbing against suspension parts or servo horns, and retighten fasteners to recommended torque.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved