TRAXXAS Telluride 4x4 Main Shaft Aluminium with Hardened Ends TEL025 by GPM  [TEL025]

TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025
Price:
NZD$32.39
Brand:
GPM
Model:
TEL025
GTIN:
4894538121735
Condition:
Brand New
Write a review
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"

Aluminium main shaft for stronger drivetrains

This aluminium main shaft with hardened steel end fittings is an aftermarket replacement designed for TRAXXAS Telluride 4x4 RC vehicles. The construction uses an aluminium core and hardened steel terminations so wear concentrates at the contact points with gears and bearings, helping extend service life compared with a plain shaft.

Supplied as a single pcs unit, the shaft is intended to fit the Telluride 4x4 platform noted in the specifications. Removal of the gearbox or axle cover is usually required to swap the original shaft, followed by a careful check of gear mesh and bearing alignment. Small adjustments to pinion/spur spacing or bearing preload are common to ensure smooth running after replacement.

When fitting, make sure the steel ends are fully seated in their bearings and that axial play is controlled. Perform a short low-load test run after installation to confirm there is no binding and that rotation is smooth. Periodic checks of the hardened ends and bearings will reveal early wear and prevent further gear damage.

Specifications

  • Item: Main shaft
  • Material: Aluminium shaft with hard steel ends
  • Model Number: TEL025
  • Compatibility: TRAXXAS Telluride 4x4

Ideal for replacing worn shafts or adding a simple durability upgrade to your TRAXXAS Telluride 4x4; check fit and mesh during installation for best results.

This item is compatible with

  • TRAXXAS TELLURIDE 4X4

Is any machining required to fit TEL025?

No machining is expected for standard Telluride 4x4 gearboxes, but verify bearing seats and shaft orientation before final reassembly.

Can I reuse my old shaft hardware?

In many cases you can, but replace any worn circlips or spacers and inspect bearings to ensure secure seating of the hardened ends.

Will this change drivetrain balance?

Weight differences are minor; however, confirm alignment and test under low load to rule out vibration or binding after fitting.

Is TEL025 suitable for trail or hard off-road use?

It is an aftermarket durability-focused component; suitability depends on your drivetrain setup and driving conditions, but hardened ends help resist wear in harsher use.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved