TRAXXAS TRX4 Brass Front Adjustable C Hub 28pcs TRX4019AX by GPM  [TRX4019AX]

TRAXXAS TRX4 TRAIL CRAWLER Brass Adjustable Front C Hub - 28pc set - GPM TRX4019AX
Price:
NZD$70.21
Brand:
GPM
Model:
TRX4019AX
GTIN:
4894538345360
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
category
Write a review
alt="TRAXXAS TRX4 TRAIL CRAWLER Brass Adjustable Front C Hub - 28pc set - GPM TRX4019AX" title="TRAXXAS TRX4 TRAIL CRAWLER Brass Adjustable Front C Hub - 28pc set - GPM TRX4019AX"
alt="TRAXXAS TRX4 TRAIL CRAWLER Brass Adjustable Front C Hub - 28pc set - GPM TRX4019AX" title="TRAXXAS TRX4 TRAIL CRAWLER Brass Adjustable Front C Hub - 28pc set - GPM TRX4019AX"
alt="TRAXXAS TRX4 TRAIL CRAWLER Brass Adjustable Front C Hub - 28pc set - GPM TRX4019AX" title="TRAXXAS TRX4 TRAIL CRAWLER Brass Adjustable Front C Hub - 28pc set - GPM TRX4019AX"
alt="TRAXXAS TRX4 TRAIL CRAWLER Brass Adjustable Front C Hub - 28pc set - GPM TRX4019AX" title="TRAXXAS TRX4 TRAIL CRAWLER Brass Adjustable Front C Hub - 28pc set - GPM TRX4019AX"

Upgraded Front C-Hub Assembly

This 28pcs brass front C-hub kit by GPM is an aftermarket replacement set made for TRAXXAS TRX4 trail crawlers. It mounts between the front gearbox and knuckle arms to link the steering components and provides a stable platform for changing damper height and tilt during setup. The kit replaces factory linkage points and includes hardware intended to increase durability and permit multiple damper locations.

Key elements are solid brass C-hubs used both structurally and as ballast, stainless steel king pins to replace stock plastic pins for firmer pivoting, and assorted collars and screw lengths to adjust damper clearance and mounting height. A mix of round and flat head screws is included so you can assemble different collar stacks, tweak damper angle, and fit tie rods without modifying parts.

Fitment notes: the assembly sits between the front gearbox and knuckle arms and requires substituting the original pins and screws. Tie-rod anchoring uses 3x18 round head screws (2 pcs) where the original tied into the damper; damper screw lengths change by collar stack - 0 collars 3x14, 1 collar 3x16, 2 collars 3x18, 3 collars 3x20 - giving stepped changes to damper height and angle. Each brass hub adds about 49g of front-end mass when installed.

Packing includes

  • C-Hub - 2pcs
  • King Pin - 4pcs
  • Stainless Steel Flat Head Screws 2.5x10 - 6pcs
  • Stainless Steel Round Head Screws 3x14 - 2pcs
  • Stainless Steel Round Head Screws 3x16 - 2pcs
  • Stainless Steel Round Head Screws 3x18 - 4pcs
  • Stainless Steel Round Head Screws 3x20 - 2pcs
  • Aluminum Collar 3x6x2 - 6pcs

Compatible Models

  • TRAXXAS-1/10 TRX4 DEFENDER TRAIL CRAWLER
  • TRAXXAS-1/10 TRX4 TACTICAL UNIT-82066-4
  • TRAXXAS-1/10 TRX4 FORD BRONCO 82046-4
  • TRAXXAS-1/10 TRX-4 BLAZER 82076-4
  • TRAXXAS-1/10 TRX-4 MERCEDES-BENZ G500
  • TRAXXAS-1/10 TRX-6 MERCEDES-BENZ-88096-4

For TRX4 enthusiasts after a heavier, more serviceable front mount with selectable damper offsets, this GPM brass C-hub kit gives direct-replacement parts and collar/screw options to fine tune front geometry and response.

Is this a direct bolt-on for TRX4 models?

Yes, the kit is intended as a direct aftermarket replacement for compatible TRX4 variants listed in the compatibility box, using supplied screws and collars for correct fit.

Which screw length do I use for a single collar?

Use the 3x16 round head screws when you fit one aluminum collar between the hub and damper mount to set the desired height.

Will brass hubs corrode if exposed to wet conditions?

Brass resists rust but should be rinsed and dried after wet runs. Periodic inspection of screws and king pins is recommended for long-term reliability.

Can I convert the hubs to left and right bias weights?

Yes, each hub acts as about 49g of ballast, so you can install one side only or mix with other weights to adjust balance for specific terrain or handling preferences.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved