TRAXXAS X-MAXX Rear Knuckle Upgrade Aluminium Arms with Collars - TXM022N by GPM  [TXM022N]

TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N
Price:
NZD$112.10
Brand:
GPM
Model:
TXM022N
GTIN:
4894538282245
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
category
Write a review
alt="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N" title="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N"
alt="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N" title="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N"
alt="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N" title="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N"
alt="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N" title="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N"
alt="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N" title="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N"
alt="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N" title="TRAXXAS X-MAXX Aluminum Rear Knuckle Arms With Collars 2pc set - GPM TXM022N"

Aluminium rear knuckles with precision POM collars

These aluminium rear knuckle arms incorporate POM collars to stabilise CVDs and wheel bearings on X-MAXX chassis. They are intended to cut lateral play at the knuckle so steering geometry stays more consistent through rough use.

Manufactured from 6061 T6 aluminium and matched with POM collars, the parts reduce bearing clearance for a snug location while allowing enough compliance to avoid bearing compression.

Installation is straightforward for the compatible models listed below and preserves steering response without extra complexity. The geometry is designed to resist deformation under load and to allow routine servicing.

Note: the conversion requires fitting 20x27x4 bearings; confirm size before you start the swap.

Compatible Models

  • TRAXXAS-1/5 4WD X-MAXX 6S
  • TRAXXAS-1/5 ELECTRIC 4WD X-MAXX 8S MONSTER TRUCK

Fit these arms when you want a firmer bearing seat and steadier steering on TRAXXAS X-MAXX 1/5 4WD rigs, and be sure to install the specified 20x27x4 bearings.

Can I use these on a modded X-MAXX?

They suit the TRAXXAS X-MAXX 1/5 4WD models listed; if your truck has altered knuckle mounts or custom geometry, double-check fitment first.

Which bearing size is needed?

You must use 20x27x4 bearings for this swap, so source replacements or verify you have spares before fitting.

Are these arms stronger than stock?

Machined 6061 T6 aluminium offers improved stiffness over many stock plastic knuckles, while POM collars help protect bearings from crushing.

Do I need special tools to fit them?

Basic hand tools used for normal knuckle service are sufficient, though a press or bearing driver can help fit bearings cleanly into the collars.

How often should I check the collars?

Check collars and bearings after heavy runs or crashes, and during routine servicing to catch wear before it affects steering accuracy.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved