TRX-4 Differential Bevel & Pinion 35T/10T TRX41035T by GPM  [TRX41035T]

TRAXXAS TRX4 TRAIL CRAWLER 40CR Steel Differential Bevel Gear 35T & Pinion Gear 10T - GPM TRX41035T
Price:
NZD$36.70
Brand:
GPM
Model:
TRX41035T
GTIN:
4894538380361
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
category
Write a review
alt="TRAXXAS TRX4 TRAIL CRAWLER 40CR Steel Differential Bevel Gear 35T & Pinion Gear 10T - GPM TRX41035T" title="TRAXXAS TRX4 TRAIL CRAWLER 40CR Steel Differential Bevel Gear 35T & Pinion Gear 10T - GPM TRX41035T"

Product summary

The TRX41035T is an aftermarket bevel and pinion set designed for TRX-4 type gearboxes, featuring a 35-tooth bevel mated to a 10-tooth pinion manufactured in 40CR steel. It fits into the inner front or rear gearbox to transfer drive from the transmission to the axle differential and serves as a direct service replacement.

This component is matched to the TRX-4 model list below and is intended to restore correct drivetrain engagement. Installation follows standard gearbox procedures including checking gear mesh and confirming bearing condition for reliable running.

Packing includes

  • Diff bevel gear - 1pcs
  • Pinion gear - 1pcs

Original Name / Part No:

8279?8279R

Compatible Models

  • TRAXXAS-1/10 ELECTRIC 4WD TRX4 DEFENDER TRAIL CRAWLER -82056-4
  • TRAXXAS-1/10 ELECTRIC 4WD TRX4 FORD BRONCO TRAIL CRAWLER-82046-4
  • TRAXXAS-1/10 4WD ELECTRIC TRX-4 BLAZER -82076-4
  • TRAXXAS-1/10 AND TRX-4 1972 CHEVROLET K5 BLAZER TRAIL CRAWLER-92086-4
  • TRAXXAS-1/10 AND TRX-4 CHEVROLET K10 TRAIL CRAWLER-92056-4
  • TRAXXAS-1/10 AND TRX-4 CRAWLER EQUIPPED WITH TRAXX-82034-4
  • TRAXXAS-1/10 AND TRX-4 FORD BRONCO TRAIL CRAWLER-92076-4
  • TRAXXAS-1/10 AND TRX-4 FORD F-150 RANGER XLT TRAIL CRAWLER-92046-4
  • TRAXXAS-1/10 AND TRX-4 LAND ROVER DEFENDER TRAIL CRAWLER-82056-4
  • TRAXXAS-1/10 4X4 TRX-4 SPORT HIGH TRAIL EDITION-82044-4
  • TRAXXAS-1/10 TRX-4 SPORT UNASSEMBLED KIT-82010-4
  • TRAXXAS-1/10 TRX-4 SPORT-82024-4
  • TRAXXAS-1/10 TRX-4 UNASSEMBLED KIT-82016-4
  • TRAXXAS-1/10 TRX-6 MERCEDES-BENZ G 63 AMG 6X6-88096-4
  • TRAXXAS-1/10 TRX-6 ULTIMATE RC HAULER-88086-4
  • TRAXXAS-1/10 TRX-6 ULTIMATE RC HAULER-88086-84

Fit this set as a like-for-like internal replacement for the TRX-4 bevel and pinion; confirm compatibility by cross-checking part numbers and set mesh and bearing clearance during rebuild to avoid premature wear.

Can I use this in either front or rear gearbox?

Yes, the TRX41035T set is intended for installation in the inner section of either the front or rear gearbox on compatible TRX-4 models.

Is lubrication different for 40CR steel gears?

Use appropriate gear grease or light gear oil as recommended for TRX-4 gearboxes; the 40CR steel faces benefit from a thin, even film during break-in.

Will I need to shim or change bearings?

Check bearing play and replace any worn bearings; adjust gear mesh with shims or carrier height as required to achieve correct backlash.

Does this set change gear ratio?

No, the tooth counts match the original spec so overall axle ratio remains unchanged when fitted as a direct replacement.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved