YD-2 Compatible Rear Mount - Yokomo Y2-RAC6 Aluminium  [Y2-RAC6]

Yokomo Y2-RAC6 Rear Suspension Mount of Y2-RAC for YD-2/PLUS/EX
Price:
NZD$30.68
Brand:
Yokomo
Model:
Y2-RAC6
GTIN:
0639342213856
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
Spares / Hop-ups - Yokomo - YD-2 category
Write a review

Precision fit rear mount for YD-2 A-arm SP

This aluminium rear suspension mount is engineered for the YD-2 A-arm SP rear suspension kit and forms the mounting interface between the rear suspension pins. It enforces the correct 38.5mm suspension pin spacing and a zero degree pin angle as defined by the Y2-RAC6 design.

During assembly the mount locates within the rear A-arm SP arrangement and is used in the positions before and after the rear suspension mount as required by the setup. Because the unit fixes the pin angle at 0 degrees, any rear toe tuning must be done via rear hub angle changes rather than rotating this component.

The item is a machined aluminium part intended for precision alignment and maintenance on compatible YD-2 variants, offering a direct fit for setups that need the specified 38.5mm spacing.

Specifications

  • Item: Rear suspension mount
  • Material: Aluminum
  • Model Number: Y2-RAC6
  • Compatibility: DP-YD2, DP-YD2G, DP-YD2PLS, DP-YD2EX, DP-YD2S, DP-YD2SG, DP-YD2S-PL, DP-YD2SX, DP-YD2E, DP-YD2EG, DP-YD2EPLS, DP-YD2EX2, DP-YD2ES, DP-YD2SS, DP-YD2SX2, DP-YD2SX2R, DP-YD2EXB, DP-YD2EXR, DP-YD2SX2P, DP-YD2SX3, DP-YD2SX3R, DP-YD2SX3P, DP-YD2AC, DP-YD2RAR, DP-YD2RAB, DP-YD2RAP, DP-YD2SAB, DP-YD2SAR, DP-YD2SAP, DP-YD2SSAB, DP-YD2SSAR, DP-YD2SSAP, DP-YD2RSAB, DP-YD2RSAR, DP-YD2RSAP, DP-YD2ACA, DP-YD2SAC

The Y2-RAC6 aluminium rear suspension mount ensures the prescribed 38.5mm pin spacing and a fixed 0 degree pin angle for YD-2 A-arm SP rear setups, making it a dependable service or replacement part.
Remark :
Due to limited stock availability, please notice that some Yokomo items may have to order from the factory and the ready time is around 4-6 weeks. Customer purchases the item is assumed to accept the waiting time which allows us to order directly from the manufacturer if the item is out of our warehouse.

What machining finish does the Y2-RAC6 have?

The mount is a machined aluminium component; finishes vary by batch but the part is produced to typical RC alloy tolerances for stability and fit.

Is aluminium prone to corrosion in track conditions?

Raw aluminium can show wear over time; regular cleaning and light protective coatings or anodizing can extend life in corrosive environments.

Can I reuse this mount after multiple races?

Yes, if there is no visible deformation or thread damage the aluminium mount can be reused; inspect pins and bores for wear before reinstalling.

Does the part require special maintenance?

Basic maintenance includes cleaning grit from mounting bores and checking the 38.5mm spacing; apply light anti-seize where metal contacts fasteners if desired.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved