Yokomo IB-414KB1A 11mm Hex Kingpin Ball for Aluminium Steering Block, compatible with DP-YD2  [IB-414KB1A]

Yokomo IB-414KB1A 11mm Hex socket Kingpin Ball for Aluminum Steering Block
Price:
NZD$10.11
Brand:
Yokomo
Model:
IB-414KB1A
GTIN:
0639342207121
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
Spares / Hop-ups - Yokomo - YD-2 category
Write a review

Kingpin with taller neck for camber clearance

The Yokomo IB-414KB1A kingpin ball is made for RC A-arms such as DRB and DIB that need a slightly higher neck to correct geometry or avoid interference at extreme camber angles. The 1mm taller neck delivers a measured change to arm angle without modifying the arm itself.

The threaded section conforms to the 3mm ISO standard and pairs with aluminium steering blocks that use that thread. Install these when the stock ball base contacts the arm during aggressive camber or when you want to adjust upper/lower arm angles to sharpen steering feedback and tyre contact.

Fitting is straightforward: remove the original ball from the A-arm or steering block, screw the IB-414KB1A into the mount, then cycle the suspension to verify clearance through full travel. Confirm there is no binding at the ball base and test drive to observe roll center and camber response before final tightening.

Packing includes

  • Kingpin ball - 4 pcs

Compatibility

  • DP-YD2
  • DP-YD2G
  • DP-YD2PLS
  • DP-YD2EX
  • DP-YD2S
  • DP-YD2SG
  • DP-YD2S-PL
  • DP-YD2SX
  • DP-YD2E
  • DP-YD2EG
  • DP-YD2EPLS
  • DP-YD2EX2
  • DP-YD2ES
  • DP-YD2SS
  • DP-YD2SX2
  • DP-YD2SX2R
  • DP-YD2EXB
  • DP-YD2EXR
  • DP-YD2SX2P
  • DP-YD2RPLS
  • DP-YD2AC
  • DP-YD2RX
  • DP-YD2RXR
  • DP-YD2RXP
  • DP-YD2RAR
  • DP-YD2RAB
  • DP-YD2RAP
  • DP-YD2SAB
  • DP-YD2SAR
  • DP-YD2SAP
  • DP-YD2SSAB
  • DP-YD2SSAR
  • DP-YD2SSAP
  • DP-YD2RSAB
  • DP-YD2RSAR
  • DP-YD2RSAP
  • DP-YD2ACA
  • DP-YD2RXTB
  • DP-YD2RXTP
  • DP-YD2RXTR
Remark :
Due to limited stock availability, please notice that some Yokomo items may have to order from the factory and the ready time is around 4-6 weeks. Customer purchases the item is assumed to accept the waiting time which allows us to order directly from the manufacturer if the item is out of our warehouse.

Is the taller neck version more prone to wear?

No inherent weakness is introduced by the 1mm taller neck; the ball uses the same contact geometry. Regular inspection for play and lubrication of pivot points will keep wear minimal.

Will the IB-414KB1A alter handling significantly?

The change is subtle: the raised neck slightly shifts the A-arm angle, which can improve clearance and nudge steering response. Expect small tuning effects rather than a dramatic handling change.

What is included in the package and what thread standard is used?

The kit contains four kingpin balls and the threaded portion follows the 3mm ISO standard to fit compatible aluminium steering blocks.

Copyright © 2008-2026 rcjaz.co.nz All rights reserved